SimulationCore2/Equipments/Drawworks/Drawworks_INPUTS.f90

subroutine Drawworks_INPUTS

    Use CDrillingConsoleVariables
    Use CDataDisplayConsoleVariables
    Use CHoistingVariables
    Use CSimulationVariables
    Use CSlipsEnumVariables
    Use CKellyConnectionEnumVariables
    Use CElevatorConnectionEnumVariables
    Use COperationConditionEnumVariables
    Use COperationScenariosVariables
    Use CSwingEnumVariables
    Use CUnityInputs
    Use CTdsConnectionModesEnumVariables
    Use CTdsElevatorModesEnumVariables
    Use CTdsSwingEnumVariables
    Use VARIABLES
    Use Drawworks_VARIABLES
    Use TD_StringConnectionData
    Use TD_DrillStemComponents
    
	IMPLICIT NONE
    
    
    
    Call DWMalfunction_ClutchEngage
 
    
    
    Drawworks%TransMode     = DrillingConsole%DWTransmisionLever
    Drawworks%Direction_Var = DrillingConsole%DWSwitch
    
    
    if (IsPortable) then
        if (Drawworks%Direction_Var==-1 .and. DataDisplayConsole%Clutch==1) then        !in FWD mode
            Drawworks%Conv_Ratio = Drawworks%FWD_Conv_Ratio(Drawworks%ClutchMode,Drawworks%TransMode)
        else
            Drawworks%Conv_Ratio = 1.d0
        end if
    else
        if (Drawworks%Direction_Var==-1) then        !in FWD mode
            Drawworks%Conv_Ratio = Drawworks%FWD_Conv_Ratio(Drawworks%ClutchMode,Drawworks%TransMode)
        else if (Drawworks%Direction_Var==+1) then   !in REV mode
            Drawworks%Conv_Ratio = 1.d0
        else if (Drawworks%Direction_Var==0) then    !in OFF mode
            Drawworks%Conv_Ratio = 1.d0
        end if
    end if
   
    
    
    !===> Main Brake and Eddy Brake
    Drawworks%EddyBreak   = DrillingConsole%EddyBreakLever*0.5                            !0<EddyBreakLever<100 *0.5= 50% of EddyBreakLever
    Drawworks%BrakeLeverCoefficient = DrillingConsole%BrakeLeverCoefficient               !0<BrakeLeverCoefficient<100
    if ( Drawworks%BrakeLeverCoefficient<10.d0 ) then
        Drawworks%BrakeLeverCoefficient = 10.d0
    end if
    Drawworks%ManualBreak = 100.d0-((100.d0-DrillingConsole%DWBreak)*(100.d0/Drawworks%BrakeLeverCoefficient))        !0<DWBrake<100              20
    if ( Drawworks%ManualBreak<0.d0 ) then
        Drawworks%ManualBreak = 0.d0
    end if
    if ( IsPortable .and. DrillingConsole%ParkingBrakeBtn==1 ) then
        Drawworks%ManualBreak = 100.d0
        DrillingConsole%ParkingBrakeLed = 1
    else
        DrillingConsole%ParkingBrakeLed = 0
    end if
    
    
    
    !===> Brake Load (Main Brake)
    Drawworks%BreakLoad = Hoisting%DrillingLineBreakingLoad            ![Lbf]
    Drawworks%BreakLoad = 4.448221619*Drawworks%BreakLoad     ![N]
    
    
    
    !===> F_fastline
    Drawworks%F_fastline = real(TD_DrawworksLoadInput)        ![Lbf]
    Drawworks%F_fastline = 4.448221619*Drawworks%F_fastline   ![N]
    
    
    
    !===> min&max Hook Height
    if ( Hoisting%DriveType==1 .and. Get_OperationCondition()==OPERATION_DRILL ) then
        if ( Get_Swing()==SWING_WELL_END .and. Get_KellyConnection()==KELLY_CONNECTION_NOTHING ) then
            DW_DrillModeCond = 1
            Drawworks%min_Hook_Height = TD_TopJointHeight+HKL-RE                       ![ft]  HKL=63.76=Kelly Ass. Height , RE=Release
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_KellyConnection()==KELLY_CONNECTION_SINGLE ) then
            DW_DrillModeCond = 2
            Drawworks%min_Hook_Height = TD_TopJointHeight+HKL+PL-RE                    ![ft]  PL=30=Pipe Lenght
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_KellyConnection() == KELLY_CONNECTION_STRING ) then
            DW_DrillModeCond = 3
            Drawworks%min_Hook_Height = 21.44d0-RE                                     ![ft]  ?????????? check  21.44=(TD_KellyConst-TD_KellyElementConst)
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        else if ( Get_Swing()==SWING_MOUSE_HOLE_END .and. Get_KellyConnection()==KELLY_CONNECTION_NOTHING ) then
            DW_DrillModeCond = 4
            Drawworks%min_Hook_Height = 66.d0-RE                                       ![ft]
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        else if ( Get_Swing()==SWING_MOUSE_HOLE_END .and. Get_KellyConnection()==KELLY_CONNECTION_SINGLE ) then
            DW_DrillModeCond = 5
            Drawworks%min_Hook_Height = 65.1d0-RE                                      ![ft]
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        else if ( Get_Swing()==SWING_RAT_HOLE_END ) then
            DW_DrillModeCond = 6
            Drawworks%min_Hook_Height = 66.d0-RE                                       ![ft]
            Drawworks%max_Hook_Height = 120.d0                                         ![ft]
        end if
    else if ( Hoisting%DriveType==1 .and. Get_OperationCondition()==OPERATION_TRIP ) then
        if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_NOTHING ) then
            DW_DrillModeCond = 7
            Drawworks%min_Hook_Height = 18.38d0                                        ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_STAND ) then
            DW_DrillModeCond = 8
            Drawworks%min_Hook_Height = TD_TopJointHeight+HL+SL-(3.d0*RE)              ![ft]  HL=17.81=Hook Assy , SL=90=Stand Length , 3: chon meghdari az toole loole(tool joint) dakhele elevator gharar migirad
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_SINGLE ) then
            DW_DrillModeCond = 9
            Drawworks%min_Hook_Height = TD_TopJointHeight+HL+PL-(3.d0*RE)              ![ft]  3: chon meghdari az toole loole(tool joint) balaye elevator mimanad
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_STRING ) then
            DW_DrillModeCond = 10
            Drawworks%min_Hook_Height = 18.5d0-RE                                      ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_MOUSE_HOLE_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_NOTHING ) then
            DW_DrillModeCond = 11
            Drawworks%min_Hook_Height = 19.38d0-RE                                     ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_MOUSE_HOLE_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_SINGLE ) then
            DW_DrillModeCond = 12
            Drawworks%min_Hook_Height = 17.73d0-RE                                     ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_RAT_HOLE_END ) then
            DW_DrillModeCond = 13
            Drawworks%min_Hook_Height = 27.41d0-RE                                     ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_LATCH_STRING ) then
            DW_DrillModeCond = 14
            Drawworks%min_Hook_Height = 18.38d0                                        ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_LATCH_SINGLE ) then
            DW_DrillModeCond = 25   !warning & collision
            Drawworks%min_Hook_Height = 18.38d0   !?????????????????                                     ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_MOUSE_HOLE_END .and. Get_ElevatorConnection() == ELEVATOR_LATCH_SINGLE ) then
            DW_DrillModeCond = 26
            Drawworks%min_Hook_Height = 10.38d0  !?????????????????                                      ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        else if ( Get_Swing()==SWING_WELL_END .and. Get_ElevatorConnection() == ELEVATOR_LATCH_STAND ) then
            DW_DrillModeCond = 27
            Drawworks%min_Hook_Height = 18.38d0    !?????????????????                                    ![ft]
            Drawworks%max_Hook_Height = 140.d0                                         ![ft]
        end if
    else if ( Hoisting%DriveType==0 ) then
        if ( Get_TdsSwing()==TDS_SWING_TILT_END ) then
            if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_LATCH_SINGLE ) then
                DW_DrillModeCond = 15
                Drawworks%min_Hook_Height = 15.0d0                                     ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_SINGLE ) then
                DW_DrillModeCond = 16
                Drawworks%min_Hook_Height = 15.0d0                                     ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_NOTHING ) then
                DW_DrillModeCond = 17
                Drawworks%min_Hook_Height = 15.0d0                                     ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            end if
        else if ( Get_TdsSwing()==TDS_SWING_OFF_END ) then
            if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_LATCH_STRING ) then
                DW_DrillModeCond = 18
                Drawworks%min_Hook_Height = max(16.0d0,TD_TopJointHeight)              ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_STRING ) then
                DW_DrillModeCond = 19
                Drawworks%min_Hook_Height = TD_TopJointHeight                          ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_STRING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_NOTHING ) then
                DW_DrillModeCond = 20
                Drawworks%min_Hook_Height = TD_TopJointHeight                          ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_NOTHING ) then
                DW_DrillModeCond = 21
                Drawworks%min_Hook_Height = max(16.0d0,TD_TopJointHeight)              ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_LATCH_STAND ) then
                DW_DrillModeCond = 22
                Drawworks%min_Hook_Height = max(16.0d0,TD_TopJointHeight)              ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_NOTHING .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_STAND ) then
                DW_DrillModeCond = 23
                Drawworks%min_Hook_Height = max(16.0d0,TD_TopJointHeight)              ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            else if ( Get_TdsConnectionModes()==TDS_CONNECTION_SPINE .and. Get_TdsElevatorModes()==TDS_ELEVATOR_CONNECTION_NOTHING ) then
                DW_DrillModeCond = 24
                Drawworks%min_Hook_Height = TD_TopJointHeight                          ![ft]
                Drawworks%max_Hook_Height = 140.d0                                     ![ft]
            end if
        end if
    end if
    
    
    
    !print* , 'DW_DrillModeCond=' , DW_DrillModeCond
    !!print* , 'Drawworks%min_Hook_Height=' , Drawworks%min_Hook_Height
    !!print* , 'Drawworks%max_Hook_Height=' , Drawworks%max_Hook_Height
    !print* , 'Drawworks%Hook_Height_final=' , Drawworks%Hook_Height_final
    !print*, 'TD_DrillStemComponentsNumbs2=' , TD_DrillStemComponentsNumbs
    !print*, 'TD_TopJointHeight2=' , TD_TopJointHeight
    !print*, 'TD_DrillStemTotalLength2=', TD_DrillStemTotalLength
    
    
    
    
    !===> SLIPS SET , No Motion
    if ( Hoisting%DriveType==1 .and. Get_Slips() == SLIPS_SET_END .and. Get_KellyConnection() == KELLY_CONNECTION_STRING ) then
        Drawworks%ManualBreak = 100.d0
        Drawworks%N_ref       = 0.d0
    end if
    
    if ( Hoisting%DriveType==0 .and. Get_Slips() == SLIPS_SET_END .and. (Get_TdsConnectionModes()==TDS_CONNECTION_SPINE .or. Get_TdsConnectionModes()==TDS_CONNECTION_STRING) ) then
        Drawworks%ManualBreak = 100.d0
        Drawworks%N_ref       = 0.d0
    end if
    
    !if ( Get_Slips() == SLIPS_SET_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_STRING .and. Drawworks%motion==+1 ) then
    !    Drawworks%ManualBreak = 100.d0
    !    Drawworks%N_ref       = 0.d0
    !!else if ( Get_Slips() == SLIPS_SET_END .and. Get_ElevatorConnection() == ELEVATOR_CONNECTION_STRING .and. Drawworks%motion/=+1 ) then
    !!    Drawworks%N_ref       = 0.d0
    !!    !Call DWFixModeMotion
    !!    !print*, 'ELEVATOR_CONNECTION_STRING'
    !end if
    
    
    
    !===> Closed BOP Rams , No Motion
    !if ( PipeRam1_Situation_forTD==1 .or. PipeRam2_Situation_forTD==1 .or. ShearBop_Situation_forTD==1 ) then
    if ( ShearBop_Situation_forTD==1 .and. (any(DW_DrillModeCond==(/3,10,19,20,24/))) ) then
        Drawworks%ManualBreak = 100.d0
        Drawworks%N_ref       = 0.d0
    end if
    
    
    
    
    
end subroutine Drawworks_INPUTS