SimulationCore2/Equipments/Pumps/Pump_OnMode_Solver.i90

# 1 "/home/admin/SimulationCore2/Equipments/Pumps/Pump_OnMode_Solver.f90"
subroutine Pump_OnMode_Solver(Pump_No)
    
    use SimulationVariables
    
    IMPLICIT NONE
    INTEGER :: Pump_No
    
    
    
    data%State%Pump(Pump_No)%Flow_Rate = data%State%Pump(Pump_No)%FlowRatePerSTK*4118.d0*0.01d0*(data%State%Pump(Pump_No)%Speed/data%State%Pump(Pump_No)%Trans_Ratio)                                 ![gpm]
    data%State%Pump(Pump_No)%Max_FlowRate = data%State%Pump(Pump_No)%FlowRatePerSTK*4118.d0*0.01d0*data%State%Pump(Pump_No)%MaxSPM                                                                    ![gpm]
    data%State%Pump(Pump_No)%HorsePower = ((data%State%Pump(Pump_No)%Flow_Rate/0.01d0)*data%State%Pump(Pump_No)%StandPipe_Pressure)/(168067.d0*data%State%Pump(Pump_No)%Mech_Efficiency)              ![HHP]
!data%State%Pump(Pump_No)%Max_Horsepower = ((data%State%Pump(Pump_No)%Flow_Rate/0.01d0)*data%State%Pump(Pump_No)%Max_Pressure)/(168067.d0*data%State%Pump(Pump_No)%Mech_Efficiency)               ![HHP]
    data%State%Pump(Pump_No)%Max_Horsepower = (data%State%Pump(Pump_No)%Flow_Rate*data%State%Pump(Pump_No)%Max_Pressure)/(1714.d0*data%State%Pump(Pump_No)%Mech_Efficiency)
! if ( data%State%Pump(Pump_No)%StandPipe_Pressure>data%State%Pump(Pump_No)%Max_Pressure ) then   ! in shart check shavad
! !if ( (data%State%Pump(Pump_No)%StandPipe_Pressure*data%State%Pump(Pump_No)%Flow_Rate)>(1714.d0*data%State%Pump(Pump_No)%Max_Horsepower*data%State%Pump(Pump_No)%Mech_Efficiency) ) then
!     data%State%Pump(Pump_No)%Flow_Rate = (1714.d0*data%State%Pump(Pump_No)%Mech_Efficiency*data%State%Pump(Pump_No)%Max_Horsepower)/data%State%Pump(Pump_No)%StandPipe_Pressure                   ![gpm]
!     data%State%Pump(Pump_No)%Speed     = ( data%State%Pump(Pump_No)%Flow_Rate/(data%State%Pump(Pump_No)%FlowRatePerSTK*4118.d0*0.01d0) )*data%State%Pump(Pump_No)%Trans_Ratio                     ![rpm]
! end if
        
    data%State%Pump(Pump_No)%SoundSPM = INT(data%State%Pump(Pump_No)%Speed/data%State%Pump(Pump_No)%Trans_Ratio)              ![SPM]                                                                        ![spm]
    
    If (data%State%Pump(Pump_No)%Flow_Rate>0.d0) Then
        data%State%Pump(Pump_No)%Open_Close = 1
    Else
        data%State%Pump(Pump_No)%Open_Close = 0
    End if
    
    
    
        
        
end subroutine Pump_OnMode_Solver